Camera Mounts and Assorted 3D Printed Parts

Questions about bike hire abroad and everything light bike related. No off-topic chat please

Moderators: robbosmans, Moderator Team

aquilinx
Posts: 19
Joined: Mon Jun 22, 2020 3:47 am

by aquilinx

WheresWaldo wrote:
Mon Oct 25, 2021 4:08 pm
@aquilinx

Take a look at this link, https://a360.co/3Gk1ZbT

It pushes the cateye back 20 mm. But is will be lower than your picture by around 8 mm. I need to do that to make up for anything molded into the shell of the Specialized saddle. Not all of them are completely flat on the bottom. I didn't change the angle from the standard that Speciailized uses on the SWAT taillight.
WheresWaldo wrote:
Mon Oct 25, 2021 4:08 pm
@aquilinx

Take a look at this link, https://a360.co/3Gk1ZbT

It pushes the cateye back 20 mm. But is will be lower than your picture by around 8 mm. I need to do that to make up for anything molded into the shell of the Specialized saddle. Not all of them are completely flat on the bottom. I didn't change the angle from the standard that Speciailized uses on the SWAT taillight.
thanks it looks great to me

User avatar
WheresWaldo
in the industry
Posts: 885
Joined: Fri Oct 13, 2006 12:52 am
Location: North Carolina

by WheresWaldo

Okay I will post it within the next hour, and provide a link.

by Weenie


Visit starbike.com Online Retailer for HighEnd cycling components
Great Prices ✓    Broad Selection ✓    Worldwide Delivery ✓

www.starbike.com



User avatar
WheresWaldo
in the industry
Posts: 885
Joined: Fri Oct 13, 2006 12:52 am
Location: North Carolina

by WheresWaldo


aquilinx
Posts: 19
Joined: Mon Jun 22, 2020 3:47 am

by aquilinx

WheresWaldo wrote:
Mon Oct 25, 2021 8:54 pm
@aquilinx

http://shpws.me/SRuG
Thanks!

User avatar
WheresWaldo
in the industry
Posts: 885
Joined: Fri Oct 13, 2006 12:52 am
Location: North Carolina

by WheresWaldo

Don't know why I forgot to enable this adapter, but here it is now. Trek Integrated Seatpost Taillight Mount to Cycliq FLY6ce Gen 3 mount adapter.
http://shpws.me/SAPb
Image

User avatar
WheresWaldo
in the industry
Posts: 885
Joined: Fri Oct 13, 2006 12:52 am
Location: North Carolina

by WheresWaldo

Got my answer, thanks

User avatar
WheresWaldo
in the industry
Posts: 885
Joined: Fri Oct 13, 2006 12:52 am
Location: North Carolina

by WheresWaldo

Finished up two new Varia mounts for Giant MY16+ Defy Advanced and TCR Advanced can be fitted anywhere along the seat mast, ideally just below the topper.
http://shpws.me/STmj TCR version
http://shpws.me/STmd Defy Advanced

User avatar
WheresWaldo
in the industry
Posts: 885
Joined: Fri Oct 13, 2006 12:52 am
Location: North Carolina

by WheresWaldo

Shapeways is doing a sale for Cyber Monday. Works on anyone's stuff, not just the stuff I design.
Image

User avatar
WheresWaldo
in the industry
Posts: 885
Joined: Fri Oct 13, 2006 12:52 am
Location: North Carolina

by WheresWaldo

Shapeways has extended Cyber Monday to Cyber Tuesday also
​​​​​​​Image

kode54
Posts: 3749
Joined: Tue May 23, 2006 9:39 pm

by kode54

Hey Bud,

Do you plan to make any Hammerhead Karoo2 mounts that replaces the Garmin adapter interface?
There's the single center screw and the K-Edge 2-bolt mount as well.

Just curious as I prefer the locking mechanism of the K2 v2 than the Garmin adapter interface.
- Factor Ostro VAM Disc
- Factor LS Disc
- Specialized Aethos Disc
- Sturdy Ti Allroad Disc
- Guru Praemio R Disc

User avatar
WheresWaldo
in the industry
Posts: 885
Joined: Fri Oct 13, 2006 12:52 am
Location: North Carolina

by WheresWaldo

@kode54

I haven't seen the K2 interface, If you could send me one or point me to where I can get a K2 mount I can make an interface for the K-Edge and Enve mounts.

kode54
Posts: 3749
Joined: Tue May 23, 2006 9:39 pm

by kode54

I have to dig mine out. I put the Garmin adapter in mine...which made the transition easier across all bikes. But that means, there's the Garmin puck, the K2 Garmin adapter, then the Karoo2 GPS computer.

MadCAD makes a few...but not just the puck...which I'm hoping can just sit inside the out front cavity and held by either one center M3 or two side by side M3 bolts.
https://www.shapeways.com/product/J86CU ... 3&li=shops
- Factor Ostro VAM Disc
- Factor LS Disc
- Specialized Aethos Disc
- Sturdy Ti Allroad Disc
- Guru Praemio R Disc

User avatar
WheresWaldo
in the industry
Posts: 885
Joined: Fri Oct 13, 2006 12:52 am
Location: North Carolina

by WheresWaldo

Here is something I didn't know about Pinarello, apparently they only use two different seat post profiles and all but a single line uses the same profile as the Dogma F# series. The only oddball appears to be the Dogma F which uses a slimmer post.

Sent to one of my mount purchasers from Pinarello:
All of our models from the Gan to the Dogma F12 use the same seat post shape and same dimensions. The seatpost on the Grevil or K series bikes will have a “flex” post, but that would still fit into any of the bikes. So, the mount you found should work on your Prince.

The Dogma F, though, has a new, more aero shape and will not fit on any of the previous models.​

User avatar
WheresWaldo
in the industry
Posts: 885
Joined: Fri Oct 13, 2006 12:52 am
Location: North Carolina

by WheresWaldo

Parlee RZ7 Varia Mount, http://shpws.me/SUJD

raffit78
Posts: 69
Joined: Mon Feb 06, 2017 5:32 pm

by raffit78

Is it possible to integrate the specialized swat tool kit and a garmin rear mount in one?

Swat tool kit is compact and uses the same holes as the 3d printed garmin Varia holes. Would be nice to integrate both if possible? Thoughts?


Sent from my iPhone using Tapatalk

by Weenie


Visit starbike.com Online Retailer for HighEnd cycling components
Great Prices ✓    Broad Selection ✓    Worldwide Delivery ✓

www.starbike.com



Post Reply