Canyon Ultimate CFR Di2

[minley1]

This is my new Canyon Ultimate CFR Di2

Fitted with Elite Wheels Drive 40 Wheels (these can in at 1303g inc tubeless tape and valves) with Continental Gran Prix 5000s 28mm tires (30g sealant in each)

Comes in at 6.64kg as pictured (Dura Ace R2900 di2 with powermeter, Canyon Garmin Mount, Dura Ace pedals, Alpitude cages and chain catcher, See.sense Ace real light mount)

Frame / fork : Canyon Ultimate CFR (Medium)
Handle Bars/Stem : Canyon CP0018
Sprint Shifters : Shimano SW-RS801-S (drops)
Bottle Cages : Alpitude Superlegera (11g each)
Chain Catcher : Alpitude Cornetto (5g)
Bartape : Supacaz Super Sticky Kush
Bar Plugs : Lucendi Sub1 (0.95g each)
Garmin mount : Canyon 3d printed (15g)
Wheelset : Elite Drive 40 (1303g, inc rim tape and valves)
Tires : Conti GP5000s TLR 28mm
Tubeless valves : Elite Wheels
Sealant : Orange Seal 30mm per tyre
Seatpost : Canyon (70g)
Saddle : Sele Italia c59 (63g)
Groupset : Shimano 9200 12s
Hanger : Sigeyi Direct Mount
Cassette : Dura Ace (11-30)
Chain : YBN SlA1210 Rainbow
Crankset : Dura Ace R2900 Powermeter
Chainrings : Dura Ace
BB : Shimano Dura Ace BB86
Pedals : Dura Ace
Rotors : Glafer Road Wave CL (160/140)
Brake pads : Shimano Dura Ace
OSPW : CyclingCeramic (65g)

[minley1]

Fitted the new Sigeyi Direct mount, also now running the YBN SLA1210 Rainbow chain using Molten Speed Wax.

[minley1]

Replaced the Supacaz bar plugs with some 3d printed one from a user on here.

To light for my scales on their own, but along with the Supacaz ones, they come in at 2g for the pair

Also fitted some rainbow Titanium cage bolts, again 2g for the pair.

[bratz]

Nicely built. Where did you get the bar plugs? I tried to get in touch with Lucendi but no reply

[minley1]

Thank you,

They were from Lucendi, I emailed him from his profile.

[bratz]

Cool. Thanks. Will try that

[AM7Jeremy]

How are you liking the wheels?

[CustomMetal]

Are you using a washer with the cages? If not you might want a wider headed bolt.. from experience with those cages

[minley1]

How are you liking the wheels?

Just a couple of rides on them, but they seem good, well built out of the box and nicely finished, need to get some more miles on them, but mostly Zwifting currently

[minley1]

Are you using a washer with the cages? If not you might want a wider headed bolt.. from experience with those cages

I'm not, but they seem the same size as the ones that came with them, just a lower profile, but I will check. Thanks for the heads up

[CustomMetal]

I changed to the wide head carbon Ti ones, bit of peace of mind

[cobc11]

IMG_4324.jpeg

Fitted the new Sigeyi Direct mount, also now running the YBN SLA1210 Rainbow chain using Molten Speed Wax.

Any noticible changes in shift quality with the YBN chain?

[minley1]

IMG_4324.jpeg

Fitted the new Sigeyi Direct mount, also now running the YBN SLA1210 Rainbow chain using Molten Speed Wax.

Any noticible changes in shift quality with the YBN chain?

It's ok, I re-indexed after fitting this and the hanger, it seems a bit noisy compared to the Shimano one, but not that noticeable. Need to get a few miles on It to really know, but on the stand it shifts fine.

[minley1]

pop

Fitted som new Galfer Wave CL Rotors (courtesy of @Rhino) also fitted a Tiparts Titanium derailleur mount screw to match some of the other Oil Slick Titanium fitted.

22g saving over the Shimano rotors.

[reedplayer]

.....

Seatpost : Canyon (70g)
....

i really like the look of this bike, consistent and restricted to the essential.

May i ask: The quoted seatpost weight above is correct?

Thank you, regards,